Extron electronic Projector PMK 300 User Manual

PMK 300 Multi-Product Projector Mounting Kit  
Installation Instructions  
N Only VersaTools products and most IP Link products can be  
3. Affix the supplied rubber pad to the side of the U-bolt clamping  
mounted using the multi-product projector mounting kit.  
plate that the projector pole contacts.  
4. Place the U-bolt around the ceiling pole and insert the two legs  
of the U-bolt through the slotted holes on the bracket’s clamping  
plate and then through the round holes on the backing brace.  
1. If necessary, remove the feet from the bottom of the device to be  
installed.  
2. Mount the device(s) to any of the bracket’s three mounting  
plates. The device(s) can be vertically mounted facing either  
up or down, whichever is most convenient. See figure 1 on the  
other side of this card.  
For a typical (1.5“ to 2.0“ diameter) pole — The supplied U-bolt  
fits a typical ceiling pole.  
For a smaller or larger pole — Locally obtain a U-bolt that fits  
the ceiling pole. The slotted holes on the bracket can accomodate  
a U-bolt for pole sizes from 1.0“ to 2.5“ in diameter.  
N On the side mounting plates, the device is typically mounted on  
the outside of the bracket.  
On the front mounting plate, the device is typically mounted on  
the inside of the bracket.  
5. Secure the bracket to the U-bolt with the included hex nuts,  
washers, and lock washers. Use a proper-sized socket to tighten  
the hex nuts.  
a. For a VersaTools or IP Link device, use two supplied  
4-40 x 3/16 screws in opposite (diagonal) corners to  
secure the device to the bracket.  
b. For a power supply, use the two included tie wraps to  
strap the power supply to the bracket.  
N The PMK 300 has a hole in the bottom plate that allows the  
projector pole to be inserted through the center of the plate  
rather than outside of the plate (see figure 2 on the other side of  
this card). To install the PMK 300 in this configuraion, slide  
the bracket up from the bottom of the pole before the projector is  
installed on the pole.  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
USA  
714.491.1500  
Fax 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort  
The Netherlands  
+31.33.453.4040  
Fax +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Building  
Singapore 368363  
+65.6383.4400  
Fax +65.6383.4664  
Extron Electronics, Japan  
Kyodo Building  
16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082 Japan  
+81.3.3511.7655  
Fax +81.3.3511.7656  
68-993-01  
Rev. B 12 05  
Rubber Pad  
PMK 300 Multi-Product Projector Mounting Kit  
Installation Instructions (continued)  
Backing  
Brace  
Backing  
Brace  
Clamping  
Plate  
Rubber Pad  
Extron  
PMK 300  
Multi Product Projector  
U-Bolt  
U-Bolt  
Mount Kit  
Clamping  
Plate  
Extron  
PMK 300  
Multi Product Projector  
Mount Kit  
Figure 1  
Figure 2  
 

Echo Paint Sprayer MS 41BP User Manual
Eiki Projector LC 350 User Manual
EVGA Computer Hardware X58 3X SLI User Manual
Extron electronic Network Cables DVI RGB 150 User Manual
Fiesta Gas Grill ESD45055 B401 User Manual
Finisar Network Card 10GBASE LRM X2 User Manual
Fisher Paykel Cooktop CE302C User Manual
Fisher Paykel Microwave Oven CMOH30SS User Manual
Fluke Thermometer 1521 User Manual
Friedrich Air Conditioner 115 Volts UE08 User Manual