3 Speed Cordless Sweeper
OWNER’S MANUAL
Model: UV647H
8.4 Volt DC
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel. : 1 (800) 798-7398
Care and Maintenance
To improve the performance and life of your unit, we recommend you do the
following:
1. Once a month clean the unit with a dry cloth, including the chamber which the
dust container fits into. Remove any hair, fiber or other materials that may have
built up in the chamber, on the rotating brush or edging tool.
2. Don’t use abrasive materials to clean the sweeper. Do not immerse the unit in
water.
Model: UV647H
8.4 Volt DC
3. Do not pick up liquids or use on wet floors.
4. Do not use on concrete, tar or similar rough surfaces .
5. Don’t pick up pieces of string or fabrics with the sweeper.
6. Do not clean tasseled or frayed carpets with the sweeper.
7. Any other servicing should be done by an authorized service representative.
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
1. Batteries discharged.
2. No power in electrical
outlet supplying charging
adapter.
1. Charge unit.
SWEEPER WILL NOT
OPERATE
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call Customer Service.
3. Unit needs servicing.
SWEEPER WILL NOT
PICK-UP
1. Dust container is full.
2. Unit needs recharging.
1. Empty dust container.
2. Charge unit.
DUST ESCAPING
FROM SWEEPER
1. Dust container is full.
1. Empty dust container.
1. Check for excessive material
on brush or in bottom of
sweeper. Remove obstruction
from brushes and/or sweeper.
2. Empty and clean dust
container.
ROTATING BRUSH
WILL NOT PICK UP
1. Unit clogged.
2. Dust container is full.
1. Sweeper Power Head
10. Dust Cup (Container)
11. Charging Jack
12. Lower Handle
13. Extension Tube
14. Telescopic Tube
15. Upper Handle
2. On / Off Switch
3. Speed Control
4. Speed Indicator Lights
5. Charging Indicator Light
6. Rotating Brush
7. Brush Cover
1. Electrical outlet not
working
2. Charging Adapter not
working
1. Check to ensure outlet is
working properly. (Easily
checked by plugging in
SWEEPER WILL NOT
CHARGE
another appliance.
3. Batteries no longer
functioning
2. Replace charging adapter
3. See battery disposal pg. 8.
16. Charging Adapter: Use Only
AD-1215-U8
8. Edging Tool
9. Gear box
Illustrations may differ from actual product.
NOTE: Cordless Sweeper Model UV647H is shipped with the
batteries uncharged. Charging of the unit for 20 hours
prior to first use is required. Use replacement battery
# XB617U only.
9
2
Assembling Your Cordless Sweeper
Battery Removal & Disposal
Before you start:
NOTE: If uncertain as to how to remove your battery pack, we suggest you take
your sweeper to a reputable small appliance service technician to have this
service performed.
Your Cordless Sweeper will require very little assembly. You should remove it from the
carton and familiarize yourself with all the components listed per the exploded view
drawing (pg.2) This will help you in the assembly and operation of your cordless
sweeper.
Follow these steps when battery removal is required.
Note: The charging adapter is shipped inside the dust cup.
This sweeper is equipped with Ni-Cd batteries and you need to dispose of them
properly. When the batteries are no longer good for use, they must be removed from
the sweeper for disposal. Do not remove the batteries for any reason other than
disposal of them. The batteries must be recycled or disposed of in accordance
with local regulations. Please consult your Yellow Pages or local recycling
center for more information.
WARNING: You must never use ordinary batteries for replacement as these
may leak and cause damage. Use only battery pack XB617U
for replacement.
Fig. 2
Fig. 1
1. In the event that the edging tool is not attached to the sweeper, insert the edging
tool into the "square" hole under the bottom of the sweeper power head. Gently
but firmly push until the edging tool locks into place. (Fig. 1)
2. Insert the lower handle. Fasten it with the captive nut and bolt that is
provided. (Fig. 2)
3. Attach the telescopic tube to the extension tube
by pushing the plastic insert into
Removal of Battery Pack
1. Remove the extention handle and dust cup container.
2. Turn unit over so that the base is facing upwards. Be careful not to turn the unit
ON. (Fig. 17)
3. Push in locking tab and lift off battery assembly. (Fig. 18)
4. Place battery assembly aside.
5. Insert the new battery assembly into unit. Ensure that locking tab snaps in place.
the bottom part of the telescopic pole.
(Fig. 3a) Push in until the "tab" on the
plastic insert snaps into the open
slot on the telescopic tube.
Push the telescopic tube
into the upper handle. (Fig. 3)
Insert the extension tube into the
CAUTION: This appliance contains Ni-Cd batteries. The batteries must
be recycled or disposed of in accordance with local
regulations. Please consult your Yellow Pages or local
recycling center for more information.
lower handle firmly in place. (Fig. 3b)
4. Place the handle into the upward
storage position.
5. Plug the charging adapter into the
Fig. 3a
sweeper power head charging jack.
Fig. 3b
Plug the charging adapter cord
into a standard electrical outlet
(120V, 60Hz.) The green charging
indicator should illuminate. If it does
not, depress the On/Off switch one
Fig. 3
time.
Fig. 17
Fig. 18
CAUTION: ALWAYS USE ADAPTOR SUPPLIED (ONLY)
WITH SWEEPER
8
3
Changing the Rotating Brush, Gear Box & Squeegee
How to Operate Your Cordless Sweeper
1. Before using, please ensure that the cordless sweeper has been initially
charged for 20 hours
WARNING:Use caution when changing the rotating brush and gear box
so that the unit does not turn ON when pressing down on the sweeper
power head.
Your cordless sweeper will only operate properly when the batteries are fully
charged. Your sweeper will operate for varying lengths of time on a full charge.
This will depend upon the type of surface being cleaned. (Longer operating time on
bare floors vs carpets.)
1. Remove the extension tube handle from the sweeper power head.
2. Turn sweeper power head upside down being careful Not to accidentally turn the
unit ON.
2. Push the On/Off switch to operate the unit. To turn off, press switch again.(Fig.4)
3. Remove the brush cover. (Fig. 10) (Refer to page 5 for detailed instructions.)
4. Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 11 & 12)
5. Lift the brush bar end cap up from the slot. (Fig. 13)
6. Pull the brush bar out of the bushing and slip off the belt to remove the brush bar.
(Fig. 14)
"On/Off" switch
7. Insert the new brush bar by first inserting the brush bar into the bushing on the end
opposite the driver belt. (Fig. 14)
8. Slip the belt over the brush bar cap.
9. Insert the brush bar into the slot. (Fig. 13)
Fig. 4
10.Insert the gear box tabs into the tab slots and push down until it clicks into place.
11.To replace the squeegee, follow instructions above for removing the gear box and
slide the squeegee out from left to right. (Fig. 15)
CAUTION: Any electronic or electrical appliance should not be
Locking
tab
Gear box
Lift
stored in or exposed to areas of high heat or humidity. Do
not store your cordless sweeper close to stoves,
radiators, furnaces or in a bathroom or bathing area.
3. To release the handle to a comfortable position, apply pressure to the top of
the sweeper head with your foot while pulling back on the handle.(Fig. 5)
Fig. 11
Fig. 10
Fig. 12
Gear box tabs
Slide
Fig. 13
Fig. 15
Fig. 14
Changing the Belt
If you find that the belt has broken and it needs replacing:
1. Remove the brush cover. (Fig. 10)
2. Push in on the locking tab of the gear box and lift gear box
to remove. (Fig. 11 & 12).
3. Push in on the locking tab of the belt access panel and lift
off to remove. (Fig. 16)
Fig. 5
4. Using a pair of tweezers, remove any leftover bits of the
belt that might still be there.
4. To change the speed of the sweeper, press on the speed control button. As you
press on it, the speed indicator light will change. If one light lights up, then you
have the low speed; two lights, medium speed; three lights, high speed.
5. If something were to jam or overload the brush bar system, the units speed
indicators will flash and the unit will stop operating, this is normal. To reset the
unit, remove the tangled object and then depress the on/off switch once and
then depress it again to restart the unit.
Fig. 16
5. Pull the brush bar out of the bushing. (Fig. 13)
6. Using a new belt, insert it into the opening until it is in all the way.
7. Using a pair of tweezers, insert them into the belt access panel and lift the new belt
over the back gear.
8. Slide the belt over the brush bar cap and then insert the brush bar into the slot.
(Fig. 13)
9. Insert the gear box tabs into the tab slots and push down until it clicks into place.
10. Press the belt access panel down until it snaps in place.
11. Replace the brush cover (Fig. 10)
4
7
Cleaning the Dust Container
To achieve the best performance, empty the dust container after each use.
2. When first started, the sweeper will start in the highest speed to prevent
overloading the unit when starting on heavy carpets. Other speeds can then be
selected by depressing the speed selector switch.
3. For best cleaning performance, use low speed on hard surfaces, medium speed
on low carpets/rugs, and use high speed on deeper carpets. These are guide
lines and you will find the optimum speed settings for your surfaces and debris to
be picked up through use and experience.
4. The sweeper will automatically try to maintain speeds on all surfaces. The unit
may appear to be pulsing during use to maintain it’s speed, this is normal. If this
occurs, please select the next highest speed to gain optimum performance.
5. To protect your sweeper and it’s components, the sweeper is provided with an
electronic overload circuit. If something were to jam or overload the brush bar
system, the units speed indicators will flash and the unit will stop operating, this
is normal. To reset the unit, remove the tangled object and then depress the
on/off switch once and then depress it again to restart the unit.
3. Replace dust container on cordless
sweeper.
1. Pull the dust
container straight
out from the side.
(Fig. 6)
4. Periodically remove the brush cover on
the front of the cordless sweeper and
remove any build up of lint, hair or fiber
on the rotating brush. To remove the
cover - grip the cover from the bottom,
pull out and
upward until the
cover unlocks
from the side
slots and tabs
Fig. 6
2. Empty dust
container contents.
(Fig. 7) If desired-
you may rinse with
water to clean the
dust container –
but dry thoroughly
before replacing on
the sweeper.
located on the
top of the
sweeper. (Fig. 8)
Fig. 7
Fig. 8
NOTE: If, when you place the sweeper to recharge and the charging indicator
light does NOT illuminate, then press the On/Off button once to turn the
sweeper off. The charging indicator light should now light up.
CAUTION: Do not accidentally turn unit on while cleaning. Do not clean
while unit is charging.
NOTE: Peak performance may only be realized after the unit has been
charged and discharged two (2) or three (3) times.
Charging the Cordless Sweeper
1. Connect the charger plug to the charging jack or hole on the back of the
sweeper. Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only
Charger AD-1215-U8. (Fig. 9)
2. This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must be
charged for a minimum of 20 hours.
IMPORTANT: To maintain peak performance of your cordless sweeper, it is
recommended that the unit be fully discharged, then
completely re-charged once a month.
3. When recharging the unit, the "On/Off" switch
must be in the "OFF" position.
CAUTION
4. The charging light indicator on the top of the
sweeper will turn solid green to indicate that the
sweeper is properly charging.
•
•
•
•
•
Use only with the battery pack supplied with the unit. (Item # XB617U)
Do not attempt to remove the battery pack from the unit to charge it.
Never attempt to throw the battery pack or unit into a fire or incinerate it.
Do not attempt to remove or damage the battery casing.
Battery must be recycled or disposed of in accordance with local
regulations at the end of it's service life. Please consult your Yellow Pages
or local recycling center for more information.
5. To recharge, repeat step #1 above. Charging
times will vary depending upon the amount
of usage between charging cycles.
Fig. 9
Note: Your sweeper is highly advanced and has electronic controls that optimize the
cleaning ability and durability of the sweeper. Please review the following instructions
carefully to ensure that all features are utilized for best performance.
STORING THE CORDLESS SWEEPER
1. When running the unit, the battery indicator will start as solid green, change to solid
red when approximately 70% of the battery life is used, and flash red when
in need of charging. The sweeper will prevent the batteries from being deeply
discharged and will indicate this by the speed indicators flashing and the sweeper
will stop operating. This is normal and all that needs to be done is to recharge the
sweeper fully. The speed indicator lights will stop flashing only after the “On/Off”
switch is set to the “Off” position. When recharging from being fully discharged, the
unit must charge for 1 hour minimum before it’s electronics will allow the unit to
operate again.
Your cordless sweeper may be stored by using the slot on the back of the upper
handle and hanging it from a screw secured to a wall or other vertical surface. Use
a #6 flat or pan head screw with the appropriate hardware for the surface that the
sweeper will be mounted on, (i.e. gyproc). Allow the screw head to extend a
approximately 3/16" from the mounting surface. Always empty your sweeper before
hanging up for storage. NOTE: Always empty the sweeper dust cup before storing.
5
6
|